Everchill Refrigerator: “Indicator light 2 flashing”
warning RV refrigerator error codes
What it means
Ambient temperature sensor fault. The board has lost a plausible reading of the air temperature around the unit. That sensor is what lets the fridge adapt its run strategy to a hot or cold environment, so a fault here typically shows up as odd cycling — running far too long, or not enough — rather than as a dead fridge.
Most likely causes
- Ambient sensor connector unseated at the main board most likely
- Ambient temperature sensor failed open or shorted common
- Damaged or pinched sensor lead less common
- Control board fault rare
Safe checks you can do yourself
- Check whether light 2 is flashing alone or paired. Alone it is the ambient sensor; with light 3 the service manual reads it as the defrost sensor, and with light 1 as the refrigerator sensor. The pairing decides which sensor you go looking for.
- Make sure lights 2 and 3 are actually flashing and not simply on. Steady lights 2 and 3 mean the panel's Power Off function is active — the fridge has been switched off at the panel and is not faulty at all.
- Pull the refrigerator fuse and reseat the thermistor connectors on the main circuit board.
- Look for a lead that has been trapped or chafed where the harness leaves the board area.
How to reset / clear Indicator light 2 flashing
- Reseat the connector, then pull the refrigerator fuse for a few minutes and reinstall it.
- Watch the panel as it powers up; a sensor fault reappears quickly once the board re-reads the circuit.
When to call a technician
The connectors are sound but light 2 keeps flashing, or the fridge cycles abnormally even with no light showing — the sensor or board should be tested by Lippert service.
Accuracy notes
Lippert's own service manual describes the panel two different ways, and they do not line up. The "Fault Display" table on page 8 assigns meanings to single lights — light 1 refrigerator sensor, 2 ambient sensor, 3 defrost sensor, 4 undervoltage, 5 overvoltage, and lights 1 and 3 together for a fan failure. The service section on pages 19-22 instead reads pairs: lights 1 and 2 for the refrigerator temp sensor in the wind channel, 2 and 3 for the defrost sensor, 3 and 4 for the freezer fan, and all lights for an under/over voltage event. Both readings are reproduced on this site because both are in the manufacturer's document; which one your panel follows appears to depend on the board and firmware revision. Count carefully how many lights are flashing before ordering a part — the pair readings come with concrete component checks, so they are the more useful place to start when two lights are flashing.
Applies to
SRD-360W TG-E · SRD-360WTG-E (LHH-2022302076) · SRD-360WTG-E (RHH-2022302077) · Everchill 10.7 cu. ft. 12V, black glass doors
FAQ
What does Everchill Refrigerator code "Indicator light 2 flashing" mean?
Ambient temperature sensor fault. The board has lost a plausible reading of the air temperature around the unit. That sensor is what lets the fridge adapt its run strategy to a hot or cold environment, so a fault here typically shows up as odd cycling — running far too long, or not enough — rather than as a dead fridge.
How do I reset Everchill Refrigerator Indicator light 2 flashing?
Reseat the connector, then pull the refrigerator fuse for a few minutes and reinstall it. Watch the panel as it powers up; a sensor fault reappears quickly once the board re-reads the circuit.
What is the most common cause of Indicator light 2 flashing on a Everchill Refrigerator?
The most likely cause is ambient sensor connector unseated at the main board.
Related · Everchill refrigerator
Refrigerator sensor fault. The control board is not getting a usable… Indicator light 3 flashing
Freezer defrost sensor fault. The board cannot read the defrost… Indicator light 4 flashing
Undervoltage alarm. The supply has dropped below what the unit will run… Indicator light 5 flashing
Overvoltage. The supply has gone above the range the electronics accept… Indicator lights 1 and 3 flashing
Fan failure. The board is not seeing the evaporator/condenser fan run as…
Sources
- Everchill 10.7 cu. ft. 12V Refrigerator (Black Glass Doors) — Troubleshooting and Service Manual — CCD-0008004 Rev 03.25.25 — "Fault Display" table (p. 8), Troubleshooting table (p. 7), "Flashing lights on the temp control panel" (pp. 19-22), Specifications (p. 8) (Lippert Components)
● Checked against 1 manufacturer document · Last verified 2026-07-27 · compiled from manufacturer documentation. Codes can vary by model year — always cross-check your unit’s manual. How we verify